* The solution assumes that there is only one stack to cut, but really there could be dozens of stacks. Take a run of the numbers 1-10000 for example. Let’s say you get 4-up on a sheet and the biggest stack that will fit in the guillotine is 500 sheets. A true cut and stack solution will print on the first stack 1-500, 501-1000, 1001-1500, 1501-2000. Ideal because the numbers can be guillotined and placed back onto a pallet for its next process. It also means I can provide these numbers first to the client and then they can wait for the other numbers (in case they had run out of stock and were in a hurry for replenishment stock). The solution doesn’t do that – instead, the first 500 stack will have the numbers 1-500, 2501-3000, 5001-5500, 7501-8000. That means not only is placement back onto the pallet confusing, but the customer has to wait for the artwork to be completely printed before even getting the first half of numbers. True, I could run the script several times to get the appropriate stacks, but why should I if the script did what I wanted? Especially if there are hundreds of stacks to print?
OK, First, you need to reread the blog. You should NOT be storing the Transaction_ID. It is a calculated value. Second, your naming is what confused me. Your Passenger table should have an autonumber PassengerID. That PassengerID should be the Foreign Key in your Reservations table. Your servation table should also have an autonumber for ReservationID. I really don’t see why you need sequential numbering in the passenger table. I can understand it in the Reservations table, but not in the passenger table. Also, I don’t see any reason for a transaction date in the passenger table. I can understand a CreateDate for when the passenger signed up.
Scott, I was able to try this as I assumed that is what I needed to do. It does not work. First, the current macro for that button is a Save Record, Close Window operation. How could I keep this and also add Code? If I just add a new button to the form and under the On Click Event put the code you suggested, I get a compile error of “method or data member not found” and ” .txtPROJECT” is highlighted. The actual field is “PROJECT ID#” and it is a long integer number. Entry I have is: Private Sub Command88_Click()
The auto-indenting feature of bullets and lists has always frustrated me. EVERY time you apply a numbered or bulleted list, you've got to set the indents. I want my lists to be indented at the very left of the page, flush with the rest of the paragraphs. But no, Microsoft insists that you want them indented by 0.63cm and hanging at 1.27cm (WHY 0.63? Why not 0.7? Or 1.0cm? But that's a question for a different session.) (I know, it's because MS is American and still uses inches etc...)
All posts and other information available at Signs 101 should be viewed as the opinion only of the poster. No claim is made that any information is accurate. As such, each reader should not rely on any information available here as accurate and should independently verify such accuracy. In addition, no claim is made that posts made here will be free from profanity, obscenity, rude, hurtful, libelous or insulting opinions of the poster. Such posts should, however, be reported to an Administrator for review.
Klaus Nordby, one of our good-natured Norwegian hecklers, has produced a ray of sunshine in the midst of a deep, dark Scandanavian winter by coming up with a wonderful little trick involving adding sequential numbers inside a paragraph. For example, 1. this is the first clause of this sentence; 2. this is the second; and 3. this is the third. That’s not a big deal to type, of course, but if you had dozens of them and you needed to insert or remove numbering frequently, doing it manually would be a hassle.
Neither the owners, employees, officers nor directors of Signs 101 shall be held responsible or liable under any legal theory for any loss or injury resulting from any post, information made available, policy, action or lack of an action at Signs 101. Your use of this website is your acceptance of these terms and conditions of use. A Eon Media,LLC Company
It sure is possible! Numbering and Section options are available in the Pages Panel menu. These options allow you to define what page starts a section and how it should be numbered. Insert a Current Page Number marker (Type>Insert Special Character>Markers>Current Page Number) in a text frame on a page or master page (recommended), select the first page of your section, open the Numbering and Section Options dialog, and enter 200 in the Start Page Numbering at: field. Hope this helps! sequentially numbering
×