Finally, open each remaining document in your Book file, go to the Pages panel, click on the thumbnail image of the first page of the document to highlight it, then click Numbering & Section Options in the Pages fly-out menu. Select Automatic Page Numbering at the top, and arabic numerals in the Page Numbering Style drop-down menu, as shown below, and click OK.
A request for numbering headings in a new document doesn't have to elicit terror—it only sounds ghoulish. If you're good with styles, you might consider a custom numbered list style, but that's too much work. Instead, use Word's built-in heading styles for a painless process. My best advice is to get the numbering scheme in place before you create the document. Trying to number headings in an existing document really can cause nightmares!
Changing the numbering display affects how pages are indicated in the InDesign document, as in the Pages panel and in the page box at the bottom of a document window. The numbering display also affects how you specify page ranges when printing and exporting the document. However, the numbering display does not change the appearance of page numbers on document pages.
Microsoft Publisher, the desktop publishing component of the Professional version of the Office Suite, can perform many time-saving tasks for busy business owners, including layout and design work. It can even help you avoid a shopping run to try to find tickets for your next employee picnic, holiday giveaway or executive board meeting. Create your own tickets, including the vital sequential ordering needed for raffles or attendance tracking, using Publisher’s page numbering. With a few tricky manipulations of the page number process, you can start running the numbers in an entirely new fashion.
I have a document where in I have to make two kinds of page numbering, A catalog (individually made) which should always start at page 1, and the other is a compiled version where the pages should be a continuous page. They both have the same content but with different output so I tried using layers, but fail to set the page numbering to auto. because setting them would affect both layers.
If you need to apply numbering within a paragraph rather than to the entire paragraph, you use Word's ListNum feature. Using the ListNum feature will allow you to take advantage of the numbering system you're currently using in your document (it will use the one you implemented most recently if you're not currently using a numbering system). The ListNum Field is available in Word 97 and later and interacts with multi-level list numbering (which should be linked to styles as set forth here). Here is a brief explanation of differences between the ListNum field and the Seq field.
Note: If you are a developer, you would do much better to use a Document Variable rather than a Document Property (so that the user can't update the version without using your macros); and to write a version control macro assigned to an “Update Version” button to take care of updating the document variable, the “Last  Updated Date”, the revision history and the document's filename (and the filepath, if you have an archive strategy for old versions), as well as taking care of transitions between draft and live status. However, that is outside the scope of this article.
First thing we need to do, is we need to jump to page 1. So double click page 1, so we know we're on it. Right click page no.1, and we need to go to this option that says 'Numbering & Section Options'. Click on him. And what we do is, we say, I want to switch it from style 1, 2, 3 to A, B, C. Actually you pick any of these in here. It's really typical to use A, B, C, but you can use any of these other numbers, just click 'OK'. You'll notice that A, B, C, D, E is being replaced out. Now what we want to do is go to our first page that we want. In our case it's E. So I don't want this. Let's get rid of our Spreads. I don't want page 1, page C, or B. I don't want this to be page1, I want this to be page 1. So I'm going to double click page E. Right click it, go to 'Numbering & Sectioning'. And just say, I'd like to start at page no. 1 using this format. Click 'OK'. What will happen is, you can see, page 1 starts here, 2, 3, 4. You see, the numbering starts here as well. All the way through, to the end of our document.
To create a running list—a list that is interrupted by other paragraphs or that spans multiple stories or documents—create a paragraph style and apply the style to paragraphs that you want to be part of the list. For example, to create a running list of the tables in your document, create a paragraph style called Tables, make a defined list part of the style, and then apply the Tables paragraph style to all paragraphs you want in your Table list.
There are three settings we need to embed in this field. The first is to tell it what kind of numbering we want to do (in this case, “First, Second, Third”), what case we want to use (upper case, title case, etc.), and a switch to tell Microsoft Word to increment the numbers. Click each of these settings as shown below, being sure to click Add to Field after each one:

If you’ve already created separate InDesign files for your chapters, you can combine them using the Book feature just fine as long as they all have the same trim size. Books look better when margins and styles are consistent throughout, but it’s not a requirement. The Book feature will allow you to synchronize styles throughout all your booked documents, but again, it’s not a requirement, and it doesn’t happen automatically.


Each document in your book can be numbered, and these numbers can be used as automatic chapter numbers. Automatic will increment from the previous document’s number, or you can choose “Same as Previous in Book” if it’s still the same chapter but broken into two or more parts, or you can arbitrarily number it anything you want to. This can save time if you have a large number of chapters that change order frequently, since the numbers will update automatically.
I have been having an issue with adding automatic page numbering to my multipage document. After adding the numbering it is showing up behind my background and objects on the page. If the page is blank, the numbering works just fine. But if I have other images or objects on the page, it lingers behind them. No matter what I do, it will not move to front of the page/objects/images. If I try and group the numbering and the objects on the page to combine them on the same layer, the numbering disappears from all remaining pages but the one I am currently on. Any help would be appreciated.
If you’re a self-taught InDesign user, you may not have been introduced to automatic page numbering, one of the biggest time-saving features in the program. InDesign allows you to set up the page numbering feature in your Master Pages. Then, as you add or shuffle pages, InDesign updates individual page numbers accordingly. You can style the page number any way you like.

InDesign’s automatic page numbers work well enough, but what about special cases? Some documents require pages to be omitted from total page counts. Other documents use several different systems. Sometimes section numbers or special codes must be included. Well, don’t start typing in those numbers manually, because InDesign can handle it—and quite gracefully, too.
If you would like the page number placed in a different location, open the Position list box and choose another option. Notice how the preview pages are updated to show you how the page number will look on the printed page. Choose OK to insert the page number code. This code will be automatically updated with the correct page number, no matter how many pages you add or subtract from the document
Microsoft Office Publisher is a software that can be used as a tool to design brochures, flyers, newsletters, and business cards; create word processing documents, marketing tools and websites; and publish websites to the web. Publisher has many templates and wizards that help users through the process of creating documents and tailoring documents to the needs of the user. You can make a multiple page document in Publisher by either duplicating pages, adding blank pages, or adding pages with text boxes on each page. Adding pages with text boxes on each page will save you a lot of time from adding the text box to each page manually. Utilizing the blank pages option is usually for creating pages that will have text pasted from the clipboard.

Warning  Making even minor changes to an outline numbering scheme won't necessarily change the initial position you've selected in the gallery, but rather may create a new gallery position, overwriting an existing one. Because of this problem, attaching numbering to styles is strongly recommended. This is covered in greater detail later in this chapter and in the chapter on Styles.
×